公司新闻

摊铺机作业时摊铺面不平整的应对

来源：/ 日期：2022-11-25

摊铺机在使用过程中，经常会出现各种大大小小的问题，今天济南摊铺机出租厂家就一起来分享一下摊铺机作业时摊铺面不平整的应对。

During the use of the paver, various problems, large and small, often occur. Today, the Jinan paver rental manufacturer would like to share with us how to deal with the uneven paving surface during the operation of the paver.

①加热温度（熨平板地板温度120度为宜）；

① Heating temperature (the temperature of screed floor should be 120 ℃);

②熨平板的平整度（底板连接不平整，底板表面不平整）；

② Flatness of screed (uneven connection of base plate and uneven surface of base plate);

③夯锤的速度（夯锤速度过低，出现坑洞；过高，表面起台）；

③ The speed of the rammer (if the rammer speed is too low, holes will appear; if it is too high, the surface will rise);

④行走速度过快，有离析；

④ The walking speed is too fast and there is segregation;

⑤螺旋高度不合适，有离析；

⑤ Improper spiral height and segregation;

⑥找平装置安装不正确（装反、超出感应范围等），起波浪；

⑥ The leveling device is installed incorrectly (installed reversely, out of the sensing range, etc.), causing waves;

⑦路基不平整，参照物不准确，摊铺厚度不一致，造成路面发白，碾压时产生推移。料温过低，也会造成摊铺面离析和开裂。

⑦ The subgrade is not smooth, the reference is not accurate, and the paving thickness is inconsistent, which causes the pavement to be white, and the rolling will cause displacement. If the material temperature is too low, it will also cause segregation and cracking of the paving surface.
济南摊铺机出租

应对办法：

Countermeasures:

作业前检查熨平板底板是否平整，底板是否粘连杂物，及时清理和调整；

Before operation, check whether the screed bottom plate is flat and whether there are sundries stuck on the bottom plate, and clean and adjust it in time;

在加热温度达到要求后，再进行摊铺工作；

Paving shall be carried out after the heating temperature reaches the requirements;

在料斗、刮板仓、螺旋处喷洒柴油，防止产生油斑；

Spray diesel oil at hopper, scraper bin and screw to prevent oil stain;

正确设定夯锤与摊铺速度，螺旋的高度以高过摊铺面的两倍高度为宜；

The tamping hammer and paving speed shall be set correctly, and the screw height shall be twice higher than the paving surface;

正确安装找平仪（或平衡梁探头高度与连线的位置）；

Correctly install the leveling instrument (or the position of the balance beam probe height and connecting line);

时刻注意观察参照物是否准确；

Always observe whether the reference object is accurate;

当路基平整度落差过大时，应提前垫料处理。

When the drop of subgrade flatness is too large, padding treatment shall be carried out in advance.

摊铺机作业时摊铺面不平整的应对相关事项就讲解到这里了，您对此有什么疑惑可以随时来我们网站咨询了解！

This is all for dealing with the unevenness of the paving surface during the operation of the paver. If you have any questions, please come to our website at any time Ask about it!

上一条：沥青路面接缝施工以及压实技术

下一条：选沥青混凝土要看性质及制备工艺