公司新闻
道路沥青在生产过程中应该注意几点
来源：/ 日期：2023-06-28
道路沥青在生产过程中应该注意以下几点：一，不能超量加料。这样会使加料的速度变慢；二，不能超量进行加工。三，不能超量进行加工。这样，就可以避免一些题发生。此外，要注意不同材料之间的磨擦力和摩擦力。
During the production process of road asphalt, the following points should be noted: firstly, excessive feeding is not allowed. This will slow down the feeding speed; 2、 Excessive processing is not allowed. 3、 Excessive processing is not allowed. In this way, some problems can be avoided. In addition, attention should be paid to the frictional force and friction force between different materials.
石油类、沥青性能好、质量高、耐腐蚀性强，而且石油类的调和材料在生产过程中也会出现一些题。如果没有合理地选择调整材料，就很难达到优良的道路结构。所以在选择调整材料时，要考虑道路沥青质量。因为道路的结构是由石油类、沥青类等组成的。
Petroleum and asphalt have good performance, high quality, and strong corrosion resistance, and some problems may arise in the production process of petroleum blending materials. If there is no reasonable selection and adjustment of materials, it is difficult to achieve excellent road structure. So when selecting and adjusting materials, it is necessary to consider the quality of road asphalt. Because the structure of roads is composed of petroleum, asphalt, etc.
调和的方法是将沥青的调和部分用水泥或者砂浆，用热熔胶粘在一起，然后用高压喷雾器进行喷射，在这种喷雾器上可以使得沥青的调整效果非常好。如果不注意，很容易发生。这个时候要注意保持清洁。
The method of blending is to use cement or mortar to stick the blended parts of asphalt together with Hot-melt adhesive, and then spray them with a high-pressure spray. This spray can make the adjustment effect of asphalt very good. If not paid attention, it can easily happen. At this time, it is important to maintain cleanliness.
另外还有一点要注意就是不能让沥青在高温下发生破坏性变形。因为沥青在高温下的发生变形是一种很危险的事情，这个时候要注意保持清洁。沥青在加工时要尽量避免沥青中掺有水分，这样就可以减少沥青中有机物和水分对路面造成破坏。
Another thing to note is that asphalt cannot undergo destructive deformation at high temperatures. Because the deformation of asphalt at high temperatures is a very dangerous thing, it is important to keep it clean at this time. When processing asphalt, it is important to avoid the addition of moisture to the asphalt as much as possible, in order to reduce the damage caused by organic matter and moisture in the asphalt to the road surface.
另外，还应该注意沥青表面是否有一层透明胶状物。如果表面有水分，则应该用干燥剂或是其他润滑剂来水分。沥青在加工过程中的表层是否会发生变形。沥青的含水率一般在40％～60％左右，沥青表面是否有氧化、脱胶等现象都可能影响到路面的养护和使用。
In addition, attention should also be paid to whether there is a layer of transparent adhesive on the asphalt surface. If there is moisture on the surface, a desiccant or other lubricant should be used to eliminate the moisture. Will the surface of asphalt deform during processing. The moisture content of asphalt is generally around 40% to 60%, and the presence of oxidation, debonding, and other phenomena on the asphalt surface may affect the maintenance and use of the road surface.
济南沥青生产厂家在生产加工时，要做好调和的准备。先是调整好道路沥青的质量。当然，调整好沥青的质量是非常重要的。如果你没有做到，那就不能说这个调和就是合格产品。
Jinan asphalt manufacturers should prepare for blending during production and processing. Firstly, adjust the quality of road asphalt. Of course, adjusting the quality of asphalt is very important. If you haven't achieved it, then you can't say that this reconciliation is a qualified product.
其次，对于调和后的沥青进行测试。这一步需要考虑很多因素。比如它在运输中会不会发生损坏。调和的方法是先用一个大铁锤将沥青搅拌，再将沥青放在水中，搅匀后放入锅内加热。
Secondly, test the blended asphalt. This step requires considering many factors. For example, will it be damaged during transportation. The method of mixing is to mix the asphalt with a big hammer, then put the asphalt in water, mix it well and put it into a pot for heating.
If it cannot be operated correctly, a wooden stick should be used to pour water in. If it cannot be controlled properly, it can be broken first with a wooden stick. Also, pay attention to ensuring that the mixed asphalt does not deform during transportation. For more related matters, come to our website Consult and learn more!
公司地址：济南市商河县贾庄镇民营经济创业园
公司名称:2023澳门正版资料免费 
备案号：